LS-CH Series 2-Wire Control Signal Lightning Arrester is designed for communication equipment such as dedicated communication lines, telemetry signals, measurement and control signals, PLC analog control systems, and 4-20mA current loops. Suitable for installation in LPZ 2-3 and subsequent lightning protection zones, it provides full-mode fine protection for two signal lines.
Featuring a plug-in module design, the product allows for easy replacement without interrupting signal transmission. The multi-level protection circuit ensures high flow rate and low residual voltage, effectively shielding signal lines from lightning-induced surges and electrostatic discharge. With a line-to-line bandwidth of 3MHz, it supports high-speed signal transmission without distortion.
| Product Features |
|
● It can simultaneously protect four communication signal lines.
|
|
● Multi level protection, high flow rate, and low residual pressure.
|
|
● The module can be hot swapped and replaced without interrupting signal transmission.
|
| ● Suitable for installation in LPZ 2-3 and subsequent lightning protection zones, it is a lightning arrester for communicationequipment such as communication dedicated lines, telemetry signals, measurement and control signals, PLC analogcontrol systems, and 4-20mA current loops. |
Product Specification
|
Standards
|
IEC 61643.21
|
|
Models
|
LS-CH5/4
|
LS-CH12/4
|
LS-CH24/4
|
LS-CH48/4
|
|
Parameter
|
|
Nominal operating voltage Un
|
5Vdc
|
12Vdc
|
24Vdc
|
48Vdc
|
|
Maximum continuous operating voltage Uc
|
6Vdc
|
18Vdc
|
32Vdc
|
60Vdc
|
|
X-X,X-C Shock rating C2
|
10kV/5kA
|
|
X-X,X-C Shock rating B2
|
4kV(10/700μs)
|
|
X-X Up@C2
|
≤15V
|
≤30V
|
≤60V
|
≤95V
|
|
X-C Up@C2
|
≤500V
|
|
X-X Up@B2
|
≤10V
|
≤25V
|
≤45V
|
≤60V
|
|
X-C Up@B2
|
≤300V
|
|
Response time tA
|
≤1ns
|
|
Load current IR
|
500mA
|
|
Line to line bandwidth fG
|
3MHz
|
|
Protective Line
|
X1-X2,X3-X4,X1,X3-C,X2,X4-C
|
Mechanical parameters
|
Installation method
|
DIN Rail 35mm
|
|
Screw torque
|
1N*m
|
|
Strip length
|
10mm
|
|
Wiring cross-sectional area
|
0.5mm²-2.5mm²
|
|
Product size
|
90mmx75mmx12mm
|
|
Shell material and flame retardant grade
|
PC+ABS,UL 94 V-0
|
|
Installation location
|
Indoor
|
|
Shell protection rating
|
IP20
|
|
Temperature range
|
-40℃…+80℃
|
|
Humidity range
|
Relative humidity≤95%
|
Notices
1. Select the model based on the signal line's nominal operating voltage (5Vdc/12Vdc/24Vdc/48Vdc).
2. Use wiring with cross-sectional area 0.5mm²-2.5mm² and tighten screws to 1N·m torque.
3. The plug-in module design allows for easy replacement, but disconnect the signal line if possible during replacement.
4. Ensure reliable grounding with ground resistance ≤4Ω to guarantee surge diversion.
5. Avoid installing in environments with strong electromagnetic interference to prevent signal distortion.
6. Regularly inspect the module for loose connections or physical damage; replace if faulty.
FAQ
Q1: What is the difference between full-mode protection and line-line mode protection?
A1: Full-mode protection covers line-line and line-ground paths, while line-line mode only protects line-line paths. This product offers full-mode fine protection.
Q2: Can it be used for both DC and AC signal lines?
A2: It is specifically designed for DC signal lines (5Vdc/12Vdc/24Vdc/48Vdc). For AC signals, choose dedicated AC signal SPD models.
Q3: What is the load current capacity of the product?
A3: The maximum load current is 500mA, suitable for most industrial control signal lines.
Q4: Does the product require external power supply?
A4: No, it is passive and does not require external power supply, drawing minimal power from the signal line.
Q5: What is the service life of the product?
A5: Under normal operating conditions, the service life is 5-8 years. It may vary based on surge frequency and environmental factors.
Product Tags:
|
|
2 Wire Control Signal SPD 5Vdc 10kV PLC Sensor Industrial Analog Loop Protection Images
|
